Macclesfield at a glance
- Postcode districts
- SK9, SK10, SK11
- Population
- about 54,345 (GeoNames)
- Council area
- Cheshire East Council
- Building approval
- Cheshire East Council building control, or a registered building control approver
- Nearest main town
- Stockport, about 10 miles
- Guide price region
- North West (−5% on West Midlands rates)
Why choose EPDM rubber roofing in Macclesfield?
For landlords with property in Macclesfield, EPDM's low upkeep is the main draw: once the outlets are kept clear and the trims are checked once or twice a year, there is little else to do. It also goes down quickly on a small roof, which keeps disruption for tenants to a minimum.
Around Macclesfield, flat roofs are common on terraced streets with flat-roofed rear kitchens and bathrooms and on 1960s and 1970s link-detached houses with flat-roofed garages and porches. The North West is one of England's wetter regions, averaging roughly 1,290 mm of rain a year, so falls, outlets and well-detailed upstands matter more than the membrane colour.
How much does an EPDM rubber roof cost in Macclesfield?
For Macclesfield we use North West rates: £1,500–£2,650 is the guide for a typical 18 m² garage roof in EPDM, VAT included. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Strip-out of the old covering, with waste taken away
- New drip and kerb trims, outlets and upstand details
- Warm-roof insulation and vapour control layer where required
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Macclesfield: questions
Do you cover Macclesfield?
Yes. Macclesfield is part of our Cheshire coverage, including postcode districts SK9, SK10, SK11. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Macclesfield?
Where the work needs approval it goes to Cheshire East Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Macclesfield?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at North West guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.