Newcastle at a glance
- Postcode districts
- BT33
- Population
- about 7,444 (GeoNames)
- Council area
- Newry, Mourne and Down District Council
- Building approval
- Newry, Mourne and Down District Council building control
- Guide price region
- Northern Ireland (−12% on West Midlands rates)
Why choose EPDM rubber roofing in Newcastle?
Rubber is a sensible pick in Newcastle where a roof sits close to bedrooms or a kitchen and you would rather avoid hot works. It suits porches, bays and dormers too, where the small area means a single sheet can cover the whole roof with no joins at all.
Around Newcastle, flat roofs are common on bungalows with flat-roofed side extensions and dormers and on terraced streets with flat-roofed rear kitchens and bathrooms. Northern Ireland averages roughly 1,150 mm of rain a year, spread over many wet days, so a roof that sheds water quickly to clear outlets lasts far longer than one that holds puddles.
How much does an EPDM rubber roof cost in Newcastle?
Guide price in Newcastle: £1,400–£2,450 for a typical 18 m² garage roof in EPDM, including VAT at Northern Ireland rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,400–£2,450 |
| Extension (20 m²), EPDM, new deck + insulation | £2,450–£4,300 |
| Porch or bay (4 m²), EPDM | £650–£1,100 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Strip-out of the old covering, with waste taken away
- Deck check and replacement of soft or rotten boards
- New drip and kerb trims, outlets and upstand details
Building control in Northern Ireland
In Northern Ireland, Technical Booklet F1 sets roof insulation at 0.18 W/m²K when a roof over a heated room is renovated or newly built, where that's feasible. The district council's building control should be contacted before work starts, and we prepare the details it asks for. More on the rules.
Which nearby areas do we also cover?
- Downpatrick · 10 mi
- Warrenpoint · 17 mi
- Newry · 18 mi
- Banbridge · 18 mi
- Carryduff · 21 mi
- Lisburn · 22 mi
EPDM rubber roofing in Newcastle: questions
Do you cover Newcastle?
Yes. Newcastle is part of our County Down coverage, including postcode districts BT33. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Newcastle?
Where the work needs approval it goes to Newry, Mourne and Down District Council building control. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Newcastle?
£1,400–£2,450 for a typical 18 m² garage roof in EPDM, at Northern Ireland guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can you walk on an EPDM roof?
Occasionally, for maintenance, yes, but EPDM is not designed as a regular walking surface. Where you need a route to plant or windows, walkway pads can be bonded on, or GRP may be a better fit.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.