Brixham at a glance
- Postcode districts
- TQ5
- Population
- about 16,693 (GeoNames)
- Council area
- Torbay Council
- Building approval
- Torbay Council building control, or a registered building control approver
- Guide price region
- South West (+3% on West Midlands rates)
Why choose EPDM rubber roofing in Brixham?
Choose EPDM in Brixham if you want a long service life without paying for a hard, walkable finish you do not need. With good detailing it typically lasts 25 years or more, and manufacturer material guarantees are available on many EPDM systems, registered for you where the system allows.
In and around Brixham, flat roofs are typically found on terraced streets with flat-roofed rear kitchens and bathrooms, and on 1930s semis with flat-roofed garages and kitchen extensions. The South West averages roughly 1,260 mm of rain a year and many roofs face wind off the Atlantic, so we specify fixings and edge details for wind uplift as well as drainage.
How much does an EPDM rubber roof cost in Brixham?
At South West guide rates, a typical 18 m² garage roof in EPDM comes to £1,650–£2,900 including VAT. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,650–£2,900 |
| Extension (20 m²), EPDM, new deck + insulation | £2,900–£5,050 |
| Porch or bay (4 m²), EPDM | £750–£1,300 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- Warm-roof insulation and vapour control layer where required
- New drip and kerb trims, outlets and upstand details
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Written workmanship guarantee, plus manufacturer guarantee registration where available
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Brixham: questions
Do you cover Brixham?
Yes. Brixham is part of our Devon coverage, including postcode districts TQ5. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Brixham?
Where the work needs approval it goes to Torbay Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Brixham?
£1,650–£2,900 for a typical 18 m² garage roof in EPDM, at South West guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.