Kingston upon Hull at a glance
- Postcode districts
- HU1, HU2, HU3, HU4, HU5, HU6, HU7, HU8 and 1 more
- Population
- about 314,018 (GeoNames)
- Council area
- Hull City Council
- Building approval
- Hull City Council building control, or a registered building control approver
- Guide price region
- Yorkshire and the Humber (−5% on West Midlands rates)
Why choose EPDM rubber roofing in Kingston upon Hull?
Choose EPDM in Kingston upon Hull if you want a long service life without paying for a hard, walkable finish you do not need. With good detailing it typically lasts 25 years or more, and manufacturer material guarantees are available on many EPDM systems, registered for you where the system allows.
Kingston upon Hull's flat roofs are mostly on lock-up garage blocks on estates, with plenty on newer estates where the first extension roofs are now being replaced too. England averages roughly 870 mm of rain a year; the Pennine side of Yorkshire is wetter and windier than the east, so we specify for the site rather than the county.
How much does an EPDM rubber roof cost in Kingston upon Hull?
Guide price in Kingston upon Hull: £1,500–£2,650 for a typical 18 m² garage roof in EPDM, including VAT at Yorkshire and the Humber rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Warm-roof insulation and vapour control layer where required
- Written workmanship guarantee, plus manufacturer guarantee registration where available
- Deck check and replacement of soft or rotten boards
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Kingston upon Hull: questions
Do you cover Kingston upon Hull?
Yes. Kingston upon Hull is part of our East Riding of Yorkshire coverage, including postcode districts HU1, HU2, HU3, HU4, HU5, HU6 and 3 more. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Kingston upon Hull?
Where the work needs approval it goes to Hull City Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Kingston upon Hull?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at Yorkshire and the Humber guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.