Kingston upon Thames at a glance
- Postcode districts
- KT1, KT2, KT5, KT6, KT3, KT9
- Council area
- Royal Borough of Kingston upon Thames
- Building approval
- Royal Borough of Kingston upon Thames building control, or a registered building control approver
- Guide price region
- London (+20% on West Midlands rates)
Why choose EPDM rubber roofing in Kingston upon Thames?
Rubber is a sensible pick in Kingston upon Thames where a roof sits close to bedrooms or a kitchen and you would rather avoid hot works. It suits porches, bays and dormers too, where the small area means a single sheet can cover the whole roof with no joins at all.
Kingston upon Thames's flat roofs are mostly on mansard and dormer loft conversions, with plenty on kitchen extensions and roof terraces behind period houses too. The Thames basin is one of the drier parts of Britain at roughly 730 mm of rain a year, but summer heat is the bigger test here: dark membranes on south-facing roofs swing a long way in temperature.
How much does an EPDM rubber roof cost in Kingston upon Thames?
For Kingston upon Thames we use London rates: £1,900–£3,350 is the guide for a typical 18 m² garage roof in EPDM, VAT included. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,900–£3,350 |
| Extension (20 m²), EPDM, new deck + insulation | £3,350–£5,850 |
| Porch or bay (4 m²), EPDM | £900–£1,500 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- Strip-out of the old covering, with waste taken away
- Written workmanship guarantee, plus manufacturer guarantee registration where available
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Warm-roof insulation and vapour control layer where required
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
- Richmond upon Thames · 3 mi
- Merton · 5 mi
- Wandsworth · 5 mi
- Hounslow · 5 mi
- Sutton · 6 mi
- Hammersmith and Fulham · 7 mi
EPDM rubber roofing in Kingston upon Thames: questions
Do you cover Kingston upon Thames?
Yes. Kingston upon Thames is part of our London coverage, including postcode districts KT1, KT2, KT5, KT6, KT3, KT9. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Kingston upon Thames?
Where the work needs approval it goes to Royal Borough of Kingston upon Thames building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Kingston upon Thames?
£1,900–£3,350 for a typical 18 m² garage roof in EPDM, at London guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.