Formby at a glance
- Postcode districts
- L37
- Population
- about 23,329 (GeoNames)
- Council area
- Sefton Council
- Building approval
- Sefton Council building control, or a registered building control approver
- Nearest main town
- Southport, about 7 miles
- Guide price region
- North West (−5% on West Midlands rates)
Why choose EPDM rubber roofing in Formby?
Rubber is a sensible pick in Formby where a roof sits close to bedrooms or a kitchen and you would rather avoid hot works. It suits porches, bays and dormers too, where the small area means a single sheet can cover the whole roof with no joins at all.
Formby's flat roofs are mostly on shops with flat-roofed rear stores below flats, with plenty on 1960s and 1970s link-detached houses with flat-roofed garages and porches too. The North West is one of England's wetter regions, averaging roughly 1,290 mm of rain a year, so falls, outlets and well-detailed upstands matter more than the membrane colour.
How much does an EPDM rubber roof cost in Formby?
Guide price in Formby: £1,500–£2,650 for a typical 18 m² garage roof in EPDM, including VAT at North West rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
Do I need building regulations approval to replace a roof with EPDM?
Often, yes. In England, Wales and Northern Ireland, re-covering more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof should be insulated towards the renovation standard where that is feasible; in Scotland, the council's building standards service decides whether a building warrant is needed.
An unheated detached garage normally falls outside these rules, and a patch repair is treated differently from a full re-cover.
In practice that means a warm roof: insulation above the deck, a vapour control layer beneath it and the EPDM on top. The extra thickness lifts the finished roof, so at survey we check door thresholds, window cills, wall flashings and upstand heights, aiming for an upstand of about 150 mm above the finished surface. Where approval is needed, we deal with building control or building standards for you. The building regulations page and our warm vs cold roof guide go into more detail.
What's included?
- Warm-roof insulation and vapour control layer where required
- Deck check and replacement of soft or rotten boards
- New drip and kerb trims, outlets and upstand details
- Written workmanship guarantee, plus manufacturer guarantee registration where available
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Formby: questions
Do you cover Formby?
Yes. Formby is part of our Merseyside coverage, including postcode districts L37. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Formby?
Where the work needs approval it goes to Sefton Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Formby?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at North West guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.
Does an EPDM roof need maintenance?
Very little. Clear leaves from outlets and gutters, look over trims and upstands once or twice a year and after storms, and keep foot traffic to a minimum.