Buckie at a glance
- Postcode districts
- AB56
- Population
- about 8,430 (GeoNames)
- Council area
- Moray Council
- Building approval
- Moray Council building standards
- Nearest main town
- Elgin, about 13 miles
- Guide price region
- Scotland (−5% on West Midlands rates)
Why choose EPDM rubber roofing in Buckie?
Rubber is a sensible pick in Buckie where a roof sits close to bedrooms or a kitchen and you would rather avoid hot works. It suits porches, bays and dormers too, where the small area means a single sheet can cover the whole roof with no joins at all.
Buckie's flat roofs are mostly on shops with flat-roofed rear stores below flats, with plenty on 1960s and 1970s link-detached houses with flat-roofed garages and porches too. Scotland averages roughly 1,570 mm of rain a year, with the west far wetter than the east, so drainage, falls and wind uplift are part of every specification we write.
How much does an EPDM rubber roof cost in Buckie?
At Scotland guide rates, a typical 18 m² garage roof in EPDM comes to £1,500–£2,650 including VAT. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- Deck check and replacement of soft or rotten boards
- Strip-out of the old covering, with waste taken away
- Written workmanship guarantee, plus manufacturer guarantee registration where available
- Warm-roof insulation and vapour control layer where required
Building standards in Scotland
In Scotland the building standards technical handbooks (Section 6 for energy) apply, and the council's building standards service decides whether a building warrant is needed. Like-for-like repairs to a roof covering can be exempt; alterations, structural work and new roofs usually need a warrant before work starts. The domestic roof benchmark is 0.12 W/m²K, applied as far as reasonably practicable on an existing roof. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Buckie: questions
Do you cover Buckie?
Yes. Buckie is part of our Moray coverage, including postcode districts AB56. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building standards for a flat roof in Buckie?
Where the work needs approval it goes to Moray Council building standards. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Buckie?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at Scotland guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.