Middlesbrough at a glance
- Postcode districts
- TS1, TS2, TS3, TS4, TS5, TS7, TS8
- Population
- about 142,707 (GeoNames)
- Council area
- Middlesbrough Council
- Building approval
- Middlesbrough Council building control, or a registered building control approver
- Guide price region
- Yorkshire and the Humber (−5% on West Midlands rates)
Why choose EPDM rubber roofing in Middlesbrough?
For landlords with property in Middlesbrough, EPDM's low upkeep is the main draw: once the outlets are kept clear and the trims are checked once or twice a year, there is little else to do. It also goes down quickly on a small roof, which keeps disruption for tenants to a minimum.
In a large town like Middlesbrough, flat roofs are commonly found on low-rise post-war blocks of flats or shops with flat-roofed rear stores below flats. England averages roughly 870 mm of rain a year; the Pennine side of Yorkshire is wetter and windier than the east, so we specify for the site rather than the county.
How much does an EPDM rubber roof cost in Middlesbrough?
For Middlesbrough we use Yorkshire and the Humber rates: £1,500–£2,650 is the guide for a typical 18 m² garage roof in EPDM, VAT included. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- Written workmanship guarantee, plus manufacturer guarantee registration where available
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Warm-roof insulation and vapour control layer where required
- New drip and kerb trims, outlets and upstand details
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
- Billingham · 2 mi
- Stockton-on-Tees · 3 mi
- Thornaby-on-Tees · 4 mi
- Yarm · 7 mi
- Redcar · 8 mi
- Hartlepool · 8 mi
EPDM rubber roofing in Middlesbrough: questions
Do you cover Middlesbrough?
Yes. Middlesbrough is part of our North Yorkshire coverage, including postcode districts TS1, TS2, TS3, TS4, TS5, TS7 and 1 more. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Middlesbrough?
Where the work needs approval it goes to Middlesbrough Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Middlesbrough?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at Yorkshire and the Humber guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can you walk on an EPDM roof?
Occasionally, for maintenance, yes, but EPDM is not designed as a regular walking surface. Where you need a route to plant or windows, walkway pads can be bonded on, or GRP may be a better fit.
Can an EPDM roof be fitted in winter?
Yes, as long as the deck is dry. The adhesives are affected by cold and damp, so very cold or wet days can delay bonding, and the roof is kept temporarily weathertight between dry spells.