Flat RoofingContractors

Flat roof systems

EPDM rubber roofing across Perth and Kinross

For EPDM rubber roofs in Perth and Kinross, expect the same careful process wherever the property is: survey, fixed written quote, strip and install, then a final walk-round. Rainfall and wind exposure vary from site to site, so trims, fixings and adhesives are chosen for the roof in front of us rather than taken from a standard list.

Roofer unrolling a single sheet of black EPDM membrane over a new OSB deck on a garage roofComputer-generated example image
Price per m²
£62–£109
Typical life
25–50 years
Manufacturer guarantees
20-year material warranties are common
Typical garage roof
£1,500–£2,650

Perth and Kinross at a glance

Largest towns
Perth, Blairgowrie and Rattray, Crieff
Postcode areas
PH
Building standards
Perth and Kinross Council
Neighbouring areas
Dundee City · Fife · Clackmannanshire · Stirling
Guide price region
Scotland (−5% on West Midlands rates)

How much does an EPDM rubber roof cost in Perth and Kinross?

Guide prices including VAT at Scotland rates. The fixed price comes after a free survey for new and replacement roofs.

JobGuide price inc VAT
Single garage (18 m²), EPDM rubber£1,500–£2,650
Extension (20 m²), EPDM, new deck + insulation£2,650–£4,650
Porch or bay (4 m²), EPDM£700–£1,200

Which flat roofs are common in Perth and Kinross?

Flat roofs in Perth and Kinross sit on newer estates where the first extension roofs are now being replaced, terraced streets with flat-roofed rear kitchens and bathrooms and shops with flat-roofed rear stores below flats. Scotland averages roughly 1,570 mm of rain a year, with the west far wetter than the east, so drainage, falls and wind uplift are part of every specification we write. Approximate 1991–2020 regional averages based on Met Office data.

Building standards in Scotland

In Scotland a building warrant is usually needed for alterations, structural work and new roofs; like-for-like repairs to a covering can be exempt. Section 6 of the technical handbooks sets a domestic roof benchmark of 0.12 W/m²K, applied as far as reasonably practicable on an existing roof. In Perth and Kinross the application goes to Perth and Kinross Council (building standards). More on the rules.

How are the joins, edges and upstands made watertight on an EPDM roof?

They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.

  • Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
  • Corners: folded rather than cut where possible, or finished with pre-formed pieces.
  • Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
  • Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
  • Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.

We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.

Which towns in Perth and Kinross do we cover?

EPDM rubber roofing in Perth and Kinross: questions

Which towns in Perth and Kinross do you cover?

All of Perth and Kinross. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.

How much does an EPDM rubber roof cost in Perth and Kinross?

£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at Scotland guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.

Which postcode areas do you cover in Perth and Kinross?

All of Perth and Kinross, including the PH postcode areas. Send your full postcode and we'll confirm.

Can an EPDM roof be fitted in winter?

Yes, as long as the deck is dry. The adhesives are affected by cold and damp, so very cold or wet days can delay bonding, and the roof is kept temporarily weathertight between dry spells.

How long does it take to fit an EPDM roof?

A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.

Does an EPDM roof need maintenance?

Very little. Clear leaves from outlets and gutters, look over trims and upstands once or twice a year and after storms, and keep foot traffic to a minimum.

Everything about EPDM rubber roofing → · All flat roofing in Perth and Kinross →

Get a fixed price for your flat roof

Free survey and a written fixed quote for replacement and new roofs. No obligation.

Call usGet a guide price