- Price per m²
- £60–£106
- Typical life
- 25–50 years
- Manufacturer guarantees
- 20-year material warranties are common
- Typical garage roof
- £1,450–£2,600
Rhondda Cynon Taf at a glance
- Largest towns
- Rhondda, Tonypandy, Pontypridd, Aberdare
- Postcode areas
- CF
- Building control
- Rhondda Cynon Taf County Borough Council
- Neighbouring areas
- Merthyr Tydfil · Caerphilly · Bridgend · Blaenau Gwent
- Guide price region
- Wales (−8% on West Midlands rates)
How much does an EPDM rubber roof cost in Rhondda Cynon Taf?
Guide prices including VAT at Wales rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,450–£2,600 |
| Extension (20 m²), EPDM, new deck + insulation | £2,600–£4,500 |
| Porch or bay (4 m²), EPDM | £700–£1,150 |
Which flat roofs are common in Rhondda Cynon Taf?
Flat roofs in Rhondda Cynon Taf sit on 1960s and 1970s link-detached houses with flat-roofed garages and porches, newer estates where the first extension roofs are now being replaced and 1930s semis with flat-roofed garages and kitchen extensions. Wales averages roughly 1,460 mm of rain a year, among the wettest in Britain, so we design for steady run-off: proper falls, clear outlets and upstands well above the finished roof. Approximate 1991–2020 regional averages based on Met Office data.
Building regulations in Wales
Welsh guidance is that most re-roofing needs building control approval, so it's worth checking whenever more than a quarter of a roof is replaced or repaired. Renovated roofs are upgraded to around 0.16 W/m²K where feasible, and new extension roofs are built to 0.13 W/m²K under the Welsh Approved Document L. In Rhondda Cynon Taf the application goes to Rhondda Cynon Taf County Borough Council. More on the rules.
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
When is EPDM the right choice, and when is another system better?
EPDM is a strong choice for simple domestic roofs that people do not walk on, such as garages, single-storey extensions, porches and dormers. It is less suited to roofs with regular foot traffic or many pipes and vents.
Where it does well: few or no joins on small roofs, flexible in cold weather, tolerant of minor building movement, and laid without a flame.
Where it falls short: the finish is plain dark rubber, it can be punctured by dropped tools or sharp debris, and it is not designed as a walking surface without added protection. Roofs with many penetrations take a lot of careful detailing.
If you want a hard, walkable finish or a complex shape, GRP fibreglass often suits better. On a tight budget, or a larger roof where a layered system is preferred, torch-on felt is worth pricing. Liquid-applied roofing handles awkward details and overlays, single-ply membranes are built for larger commercial roofs, and mastic asphalt belongs on older and heritage buildings. Our EPDM vs GRP vs felt guide sets them side by side.
Which towns in Rhondda Cynon Taf do we cover?
EPDM rubber roofing in Rhondda Cynon Taf: questions
Which towns in Rhondda Cynon Taf do you cover?
All of Rhondda Cynon Taf. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does an EPDM rubber roof cost in Rhondda Cynon Taf?
£1,450–£2,600 for a typical 18 m² garage roof in EPDM, at Wales guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which council handles building control for a flat roof in Rhondda Cynon Taf?
It depends on where the roof is: in Rhondda Cynon Taf that's Rhondda Cynon Taf County Borough Council. Welsh guidance is that most re-roofing needs building control approval, so it's worth checking whenever more than a quarter of a roof is replaced or repaired. We confirm which applies at the survey.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.
Can an EPDM roof be fitted in winter?
Yes, as long as the deck is dry. The adhesives are affected by cold and damp, so very cold or wet days can delay bonding, and the roof is kept temporarily weathertight between dry spells.
Does an EPDM roof need maintenance?
Very little. Clear leaves from outlets and gutters, look over trims and upstands once or twice a year and after storms, and keep foot traffic to a minimum.
Everything about EPDM rubber roofing → · All flat roofing in Rhondda Cynon Taf →