Bloxwich at a glance
- Postcode districts
- WS3
- Population
- about 40,000 (GeoNames)
- Council area
- Walsall Council
- Building approval
- Walsall Council building control, or a registered building control approver
- Nearest main town
- Walsall, about 2 miles
- Guide price region
- West Midlands (baseline rates)
Why choose EPDM rubber roofing in Bloxwich?
Rubber is a sensible pick in Bloxwich where a roof sits close to bedrooms or a kitchen and you would rather avoid hot works. It suits porches, bays and dormers too, where the small area means a single sheet can cover the whole roof with no joins at all.
In and around Bloxwich, flat roofs are typically found on terraced streets with flat-roofed rear kitchens and bathrooms, and on 1960s and 1970s link-detached houses with flat-roofed garages and porches. England averages roughly 870 mm of rain a year and the West Midlands sits close to that, so falls and outlets are the difference between a roof that drains and one that ponds.
How much does an EPDM rubber roof cost in Bloxwich?
At West Midlands guide rates, a typical 18 m² garage roof in EPDM comes to £1,600–£2,800 including VAT. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,600–£2,800 |
| Extension (20 m²), EPDM, new deck + insulation | £2,800–£4,900 |
| Porch or bay (4 m²), EPDM | £750–£1,250 |
Do I need building regulations approval to replace a roof with EPDM?
Often, yes. In England, Wales and Northern Ireland, re-covering more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof should be insulated towards the renovation standard where that is feasible; in Scotland, the council's building standards service decides whether a building warrant is needed.
An unheated detached garage normally falls outside these rules, and a patch repair is treated differently from a full re-cover.
In practice that means a warm roof: insulation above the deck, a vapour control layer beneath it and the EPDM on top. The extra thickness lifts the finished roof, so at survey we check door thresholds, window cills, wall flashings and upstand heights, aiming for an upstand of about 150 mm above the finished surface. Where approval is needed, we deal with building control or building standards for you. The building regulations page and our warm vs cold roof guide go into more detail.
What's included?
- Deck check and replacement of soft or rotten boards
- Warm-roof insulation and vapour control layer where required
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Strip-out of the old covering, with waste taken away
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Bloxwich: questions
Do you cover Bloxwich?
Yes. Bloxwich is part of our West Midlands coverage, including postcode districts WS3. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Bloxwich?
Where the work needs approval it goes to Walsall Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Bloxwich?
£1,600–£2,800 for a typical 18 m² garage roof in EPDM, at West Midlands guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.