Morley at a glance
- Postcode districts
- LS27
- Population
- about 57,385 (GeoNames)
- Council area
- Leeds City Council
- Building approval
- Leeds City Council building control, or a registered building control approver
- Nearest main town
- Leeds, about 4 miles
- Guide price region
- Yorkshire and the Humber (−5% on West Midlands rates)
Why choose EPDM rubber roofing in Morley?
If your Morley roof has been patched more than once and the felt is cracking or blistering, a full replacement in EPDM can be better value than another repair. The rubber stays flexible through hot summers and freezing nights, and the replacement is the right point to bring the insulation up to standard.
In and around Morley, flat roofs are typically found on 1930s semis with flat-roofed garages and kitchen extensions, and on lock-up garage blocks on estates. England averages roughly 870 mm of rain a year; the Pennine side of Yorkshire is wetter and windier than the east, so we specify for the site rather than the county.
How much does an EPDM rubber roof cost in Morley?
Guide price in Morley: £1,500–£2,650 for a typical 18 m² garage roof in EPDM, including VAT at Yorkshire and the Humber rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- Strip-out of the old covering, with waste taken away
- Warm-roof insulation and vapour control layer where required
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Deck check and replacement of soft or rotten boards
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Morley: questions
Do you cover Morley?
Yes. Morley is part of our West Yorkshire coverage, including postcode districts LS27. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Morley?
Where the work needs approval it goes to Leeds City Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Morley?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at Yorkshire and the Humber guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.