Warminster at a glance
- Postcode districts
- BA12
- Population
- about 17,490 (GeoNames)
- Council area
- Wiltshire Council
- Building approval
- Wiltshire Council building control, or a registered building control approver
- Nearest main town
- Bath, about 14 miles
- Guide price region
- South West (+3% on West Midlands rates)
Why choose EPDM rubber roofing in Warminster?
If your Warminster roof has been patched more than once and the felt is cracking or blistering, a full replacement in EPDM can be better value than another repair. The rubber stays flexible through hot summers and freezing nights, and the replacement is the right point to bring the insulation up to standard.
In and around Warminster, flat roofs are typically found on terraced streets with flat-roofed rear kitchens and bathrooms, and on shops with flat-roofed rear stores below flats. The South West averages roughly 1,260 mm of rain a year and many roofs face wind off the Atlantic, so we specify fixings and edge details for wind uplift as well as drainage.
How much does an EPDM rubber roof cost in Warminster?
For Warminster we use South West rates: £1,650–£2,900 is the guide for a typical 18 m² garage roof in EPDM, VAT included. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,650–£2,900 |
| Extension (20 m²), EPDM, new deck + insulation | £2,900–£5,050 |
| Porch or bay (4 m²), EPDM | £750–£1,300 |
Do I need building regulations approval to replace a roof with EPDM?
Often, yes. In England, Wales and Northern Ireland, re-covering more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof should be insulated towards the renovation standard where that is feasible; in Scotland, the council's building standards service decides whether a building warrant is needed.
An unheated detached garage normally falls outside these rules, and a patch repair is treated differently from a full re-cover.
In practice that means a warm roof: insulation above the deck, a vapour control layer beneath it and the EPDM on top. The extra thickness lifts the finished roof, so at survey we check door thresholds, window cills, wall flashings and upstand heights, aiming for an upstand of about 150 mm above the finished surface. Where approval is needed, we deal with building control or building standards for you. The building regulations page and our warm vs cold roof guide go into more detail.
What's included?
- Deck check and replacement of soft or rotten boards
- Warm-roof insulation and vapour control layer where required
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Strip-out of the old covering, with waste taken away
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Warminster: questions
Do you cover Warminster?
Yes. Warminster is part of our Wiltshire coverage, including postcode districts BA12. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Warminster?
Where the work needs approval it goes to Wiltshire Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Warminster?
£1,650–£2,900 for a typical 18 m² garage roof in EPDM, at South West guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can EPDM be laid over an old felt roof?
Sometimes, but we usually recommend stripping old felt first. Overlaying hides any rot or wet insulation underneath, and over a heated room a full replacement is often when insulation has to be added anyway.
Can an EPDM roof be fitted in winter?
Yes, as long as the deck is dry. The adhesives are affected by cold and damp, so very cold or wet days can delay bonding, and the roof is kept temporarily weathertight between dry spells.