- Price per m²
- £86–£138
- Typical life
- 25–35+ years
- Manufacturer guarantees
- 20–25 year guarantees on specified systems
- Typical garage roof
- £1,950–£3,150
Aberdeen City at a glance
- Largest towns
- Aberdeen, Nigg, Portlethen
- Postcode areas
- AB
- Building standards
- Aberdeen City Council
- Neighbouring areas
- Aberdeenshire · Angus · Dundee City · Moray
- Guide price region
- Scotland (−5% on West Midlands rates)
How much does a single-ply roof cost in Aberdeen City?
Guide prices including VAT at Scotland rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Commercial roof (100 m²), single-ply + insulation | £12,550–£20,700 |
| Single garage (18 m²), single-ply | £1,950–£3,150 |
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
Which flat roofs are common in Aberdeen City?
Flat roofs in Aberdeen City sit on terraced streets with flat-roofed rear kitchens and bathrooms, 1960s and 1970s link-detached houses with flat-roofed garages and porches and 1930s semis with flat-roofed garages and kitchen extensions. Scotland averages roughly 1,570 mm of rain a year, with the west far wetter than the east, so drainage, falls and wind uplift are part of every specification we write. Approximate 1991–2020 regional averages based on Met Office data.
Building standards in Scotland
In Scotland a building warrant is usually needed for alterations, structural work and new roofs; like-for-like repairs to a covering can be exempt. Section 6 of the technical handbooks sets a domestic roof benchmark of 0.12 W/m²K, applied as far as reasonably practicable on an existing roof. In Aberdeen City the application goes to Aberdeen City Council (building standards). More on the rules.
Is single-ply the right system for my roof?
Single-ply is usually the right system for medium and large flat roofs, such as shops, offices, units, surgeries, clubs and blocks, where speed of installation, light weight and long life matter. On a small domestic roof it can work well, though it is not always the most economical choice.
In its favour: lightweight; quick to lay over large areas; flame-free, as the seams are welded with hot air; long typical life; welded details at rooflights and plant; lighter-coloured membranes reflect more sunlight.
Against it: only one waterproof layer, so welding quality is critical; can be punctured by foot traffic or dropped tools without walkway protection; PVC needs separating from bitumen; repairs need compatible material and welding equipment.
For a small garage or extension, EPDM is often simpler. Where people walk regularly, GRP or a liquid system may be tougher. A multi-layer torch-on felt roof gives built-in redundancy, and on older buildings mastic asphalt may be the original material. Our commercial flat roofing page covers larger jobs.
Which towns in Aberdeen City do we cover?
Single-ply membrane roofing in Aberdeen City: questions
Which towns in Aberdeen City do you cover?
All of Aberdeen City. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does a single-ply roof cost in Aberdeen City?
£12,550–£20,700 for a 100 m² commercial roof in single-ply with insulation, at Scotland guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which council handles building standards for a flat roof in Aberdeen City?
It depends on where the roof is: in Aberdeen City that's Aberdeen City Council. In Scotland a building warrant is usually needed for alterations, structural work and new roofs; like-for-like repairs to a covering can be exempt. We confirm which applies at the survey.
Can a single-ply roof be repaired?
Yes. A compatible patch is cleaned and hot-air welded over the damage. Older membranes may need extra cleaning before they weld properly, which the team checks on site.
Does single-ply work with solar panels or a green roof?
Usually, yes. Many systems can be specified for sedum or ballasted green roofs, and solar mounts can be welded or ballasted, though the structure and wind loads must be checked first.
What is the difference between PVC and TPO roofing?
Both are thermoplastic single-ply membranes welded with hot air. PVC contains plasticisers and usually needs separating from bitumen, while TPO and FPO are polyolefin-based; the right one depends on the roof and the system specified.
Everything about single-ply membrane roofing → · All flat roofing in Aberdeen City →