- Price per m²
- £83–£133
- Typical life
- 25–35+ years
- Manufacturer guarantees
- 20–25 year guarantees on specified systems
- Typical garage roof
- £1,900–£3,050
Conwy at a glance
- Largest towns
- Colwyn Bay, Llandudno, Abergele
- Postcode areas
- LL
- Building control
- Conwy County Borough Council
- Neighbouring areas
- Denbighshire · Gwynedd · Flintshire · Wrexham
- Guide price region
- Wales (−8% on West Midlands rates)
How much does a single-ply roof cost in Conwy?
Guide prices including VAT at Wales rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Commercial roof (100 m²), single-ply + insulation | £12,150–£20,050 |
| Single garage (18 m²), single-ply | £1,900–£3,050 |
| Single garage (18 m²), EPDM rubber | £1,450–£2,600 |
| Extension (20 m²), EPDM, new deck + insulation | £2,600–£4,500 |
Which flat roofs are common in Conwy?
Flat roofs in Conwy sit on 1960s and 1970s link-detached houses with flat-roofed garages and porches, 1930s semis with flat-roofed garages and kitchen extensions and low-rise post-war blocks of flats. Wales averages roughly 1,460 mm of rain a year, among the wettest in Britain, so we design for steady run-off: proper falls, clear outlets and upstands well above the finished roof. Approximate 1991–2020 regional averages based on Met Office data.
Building regulations in Wales
Welsh guidance is that most re-roofing needs building control approval, so it's worth checking whenever more than a quarter of a roof is replaced or repaired. Renovated roofs are upgraded to around 0.16 W/m²K where feasible, and new extension roofs are built to 0.13 W/m²K under the Welsh Approved Document L. In Conwy the application goes to Conwy County Borough Council. More on the rules.
How long does a single-ply roof last, and what guarantee comes with it?
A well-installed single-ply roof typically lasts 25 to 35 years or more. Its life depends mostly on the quality of the welds, the fixing pattern, protection from foot traffic and keeping outlets clear.
Signs of trouble on an older single-ply roof include seams lifting at the edges, shrinkage pulling at upstands and corners, punctures near plant, and loose fixings under the membrane on windy sites.
Manufacturer guarantees are available on many specified single-ply systems, and they often depend on a registered build-up, an inspection and sometimes an approved installer. Where the system allows, we complete that registration on your behalf. On every re-roof you also receive our written workmanship guarantee, with the length set out in the quote, and you can ask about insurance-backed options. See the guarantees guide and maintenance guide for more.
Should a single-ply roof be mechanically fixed or adhered, and how are the seams welded?
Most commercial single-ply roofs are mechanically fixed, while adhered systems suit decks that cannot take fixings or roofs where a smooth finish is wanted. The choice depends on the deck, the wind exposure of the site and the manufacturer's specification.
| Method | How it works | Typical use |
|---|---|---|
| Mechanically fixed | Fasteners and plates hold the membrane through the insulation into the deck, hidden under the lap of the next sheet | Metal, timber and concrete decks on commercial roofs |
| Adhered | Membrane bonded to the insulation or deck with adhesive | Domestic roofs, roofs where fixings are unsuitable |
| Ballasted | Loose-laid and held down by paving, gravel or a green roof | Inverted roofs, terraces, green roofs |
Fixing patterns are worked out for the site, with more fasteners at corners and perimeters, where wind uplift is strongest.
Seams are welded by hot-air machines and hand tools that melt the overlapping edges so they fuse. Each seam is then probed along its length to find any gaps, and test welds are made at the start of the day to set the machine for the weather. On commercial jobs we also check that walkways protect the membrane around plant.
Which towns in Conwy do we cover?
Single-ply membrane roofing in Conwy: questions
Which towns in Conwy do you cover?
All of Conwy. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does a single-ply roof cost in Conwy?
£12,150–£20,050 for a 100 m² commercial roof in single-ply with insulation, at Wales guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which postcode areas do you cover in Conwy?
All of Conwy, including the LL postcode areas. Send your full postcode and we'll confirm.
Does single-ply work with solar panels or a green roof?
Usually, yes. Many systems can be specified for sedum or ballasted green roofs, and solar mounts can be welded or ballasted, though the structure and wind loads must be checked first.
How long does a commercial single-ply roof take?
A roof of around 100 m² typically takes several days, depending on strip-out, insulation, details and weather. Work is phased so the building stays weathertight and occupied areas are protected.
What is the difference between PVC and TPO roofing?
Both are thermoplastic single-ply membranes welded with hot air. PVC contains plasticisers and usually needs separating from bitumen, while TPO and FPO are polyolefin-based; the right one depends on the roof and the system specified.
Everything about single-ply membrane roofing → · All flat roofing in Conwy →