- Price per m²
- £79–£128
- Typical life
- 25–35+ years
- Manufacturer guarantees
- 20–25 year guarantees on specified systems
- Typical garage roof
- £1,800–£2,950
County Armagh at a glance
- Largest towns
- Craigavon, Portadown, Armagh
- Postcode areas
- BT
- Building control
- Armagh City, Banbridge and Craigavon Borough Council
- Neighbouring areas
- County Down · Belfast · County Tyrone · County Antrim
- Guide price region
- Northern Ireland (−12% on West Midlands rates)
How much does a single-ply roof cost in County Armagh?
Guide prices including VAT at Northern Ireland rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Commercial roof (100 m²), single-ply + insulation | £11,650–£19,150 |
| Single garage (18 m²), single-ply | £1,800–£2,950 |
| Single garage (18 m²), EPDM rubber | £1,400–£2,450 |
| Extension (20 m²), EPDM, new deck + insulation | £2,450–£4,300 |
Which flat roofs are common in County Armagh?
Flat roofs in County Armagh sit on low-rise post-war blocks of flats, 1960s and 1970s link-detached houses with flat-roofed garages and porches and bungalows with flat-roofed side extensions and dormers. Northern Ireland averages roughly 1,150 mm of rain a year, spread over many wet days, so a roof that sheds water quickly to clear outlets lasts far longer than one that holds puddles. Approximate 1991–2020 regional averages based on Met Office data.
Building control in Northern Ireland
In Northern Ireland, renovating or replacing a roof over a heated room usually means meeting Technical Booklet F1, and building control should be contacted before work starts. Technical Booklet F1 sets roof insulation at 0.18 W/m²K when a roof over a heated room is renovated or newly built, where feasible. In County Armagh the application goes to Armagh City, Banbridge and Craigavon Borough Council. More on the rules.
How long does a single-ply roof last, and what guarantee comes with it?
A well-installed single-ply roof typically lasts 25 to 35 years or more. Its life depends mostly on the quality of the welds, the fixing pattern, protection from foot traffic and keeping outlets clear.
Signs of trouble on an older single-ply roof include seams lifting at the edges, shrinkage pulling at upstands and corners, punctures near plant, and loose fixings under the membrane on windy sites.
Manufacturer guarantees are available on many specified single-ply systems, and they often depend on a registered build-up, an inspection and sometimes an approved installer. Where the system allows, we complete that registration on your behalf. On every re-roof you also receive our written workmanship guarantee, with the length set out in the quote, and you can ask about insurance-backed options. See the guarantees guide and maintenance guide for more.
Should a single-ply roof be mechanically fixed or adhered, and how are the seams welded?
Most commercial single-ply roofs are mechanically fixed, while adhered systems suit decks that cannot take fixings or roofs where a smooth finish is wanted. The choice depends on the deck, the wind exposure of the site and the manufacturer's specification.
| Method | How it works | Typical use |
|---|---|---|
| Mechanically fixed | Fasteners and plates hold the membrane through the insulation into the deck, hidden under the lap of the next sheet | Metal, timber and concrete decks on commercial roofs |
| Adhered | Membrane bonded to the insulation or deck with adhesive | Domestic roofs, roofs where fixings are unsuitable |
| Ballasted | Loose-laid and held down by paving, gravel or a green roof | Inverted roofs, terraces, green roofs |
Fixing patterns are worked out for the site, with more fasteners at corners and perimeters, where wind uplift is strongest.
Seams are welded by hot-air machines and hand tools that melt the overlapping edges so they fuse. Each seam is then probed along its length to find any gaps, and test welds are made at the start of the day to set the machine for the weather. On commercial jobs we also check that walkways protect the membrane around plant.
Which towns in County Armagh do we cover?
Single-ply membrane roofing in County Armagh: questions
Which towns in County Armagh do you cover?
All of County Armagh. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does a single-ply roof cost in County Armagh?
£11,650–£19,150 for a 100 m² commercial roof in single-ply with insulation, at Northern Ireland guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which council handles building control for a flat roof in County Armagh?
It depends on where the roof is: in County Armagh that's Armagh City, Banbridge and Craigavon Borough Council. In Northern Ireland, renovating or replacing a roof over a heated room usually means meeting Technical Booklet F1, and building control should be contacted before work starts. We confirm which applies at the survey.
Does single-ply work with solar panels or a green roof?
Usually, yes. Many systems can be specified for sedum or ballasted green roofs, and solar mounts can be welded or ballasted, though the structure and wind loads must be checked first.
Can single-ply be used on a house?
Yes. It can be used on garages, extensions and dormers, usually adhered rather than mechanically fixed. On small domestic roofs, though, EPDM or GRP is often more economical.
What is the difference between PVC and TPO roofing?
Both are thermoplastic single-ply membranes welded with hot air. PVC contains plasticisers and usually needs separating from bitumen, while TPO and FPO are polyolefin-based; the right one depends on the roof and the system specified.
Everything about single-ply membrane roofing → · All flat roofing in County Armagh →