Fleet at a glance
- Postcode districts
- GU13, GU51, GU52
- Population
- about 38,726 (GeoNames)
- Council area
- Hart District Council
- Building approval
- Hart District Council building control, or a registered building control approver
- Nearest main town
- Bracknell, about 10 miles
- Guide price region
- South East (+10% on West Midlands rates)
Why choose single-ply roofing in Fleet?
Single-ply also works on an extension or garage in Fleet if you want a light, clean finish in a pale colour. On small roofs it is usually adhered, and while it can cost more than EPDM, it gives the same welded seams and details found on commercial roofs.
In and around Fleet, flat roofs are typically found on bungalows with flat-roofed side extensions and dormers, and on shops with flat-roofed rear stores below flats. Much of the South East sits in the drier Thames catchment at roughly 730 mm of rain a year, so the usual failures are at joints, upstands and outlets rather than from sheer volume of rain.
How much does a single-ply roof cost in Fleet?
At South East guide rates, a 100 m² commercial roof in single-ply with insulation comes to £14,550–£23,950 including VAT. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Commercial roof (100 m²), single-ply + insulation | £14,550–£23,950 |
| Single garage (18 m²), single-ply | £2,250–£3,650 |
| Single garage (18 m²), EPDM rubber | £1,750–£3,100 |
| Extension (20 m²), EPDM, new deck + insulation | £3,100–£5,350 |
Should a single-ply roof be mechanically fixed or adhered, and how are the seams welded?
Most commercial single-ply roofs are mechanically fixed, while adhered systems suit decks that cannot take fixings or roofs where a smooth finish is wanted. The choice depends on the deck, the wind exposure of the site and the manufacturer's specification.
| Method | How it works | Typical use |
|---|---|---|
| Mechanically fixed | Fasteners and plates hold the membrane through the insulation into the deck, hidden under the lap of the next sheet | Metal, timber and concrete decks on commercial roofs |
| Adhered | Membrane bonded to the insulation or deck with adhesive | Domestic roofs, roofs where fixings are unsuitable |
| Ballasted | Loose-laid and held down by paving, gravel or a green roof | Inverted roofs, terraces, green roofs |
Fixing patterns are worked out for the site, with more fasteners at corners and perimeters, where wind uplift is strongest.
Seams are welded by hot-air machines and hand tools that melt the overlapping edges so they fuse. Each seam is then probed along its length to find any gaps, and test welds are made at the start of the day to set the machine for the weather. On commercial jobs we also check that walkways protect the membrane around plant.
What's included?
- Vapour control layer and warm-roof or tapered insulation as specified
- Welded details at upstands, outlets, rooflight kerbs and edge trims
- PVC, TPO or FPO membrane, mechanically fixed, adhered or ballasted
- Strip-out or preparation of the existing roof, with waste removed
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
Single-ply membrane roofing in Fleet: questions
Do you cover Fleet?
Yes. Fleet is part of our Hampshire coverage, including postcode districts GU13, GU51, GU52. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Fleet?
Where the work needs approval it goes to Hart District Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does a single-ply roof cost in Fleet?
£14,550–£23,950 for a 100 m² commercial roof in single-ply with insulation, at South East guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
How long does a commercial single-ply roof take?
A roof of around 100 m² typically takes several days, depending on strip-out, insulation, details and weather. Work is phased so the building stays weathertight and occupied areas are protected.
Can a single-ply roof be repaired?
Yes. A compatible patch is cleaned and hot-air welded over the damage. Older membranes may need extra cleaning before they weld properly, which the team checks on site.