Frome at a glance
- Postcode districts
- BA11
- Population
- about 26,203 (GeoNames)
- Council area
- Somerset Council
- Building approval
- Somerset Council building control, or a registered building control approver
- Nearest main town
- Bath, about 10 miles
- Guide price region
- South West (+3% on West Midlands rates)
Why choose single-ply roofing in Frome?
Single-ply also works on an extension or garage in Frome if you want a light, clean finish in a pale colour. On small roofs it is usually adhered, and while it can cost more than EPDM, it gives the same welded seams and details found on commercial roofs.
Frome's flat roofs are mostly on bungalows with flat-roofed side extensions and dormers, with plenty on shops with flat-roofed rear stores below flats too. The South West averages roughly 1,260 mm of rain a year and many roofs face wind off the Atlantic, so we specify fixings and edge details for wind uplift as well as drainage.
How much does a single-ply roof cost in Frome?
Guide price in Frome: £13,650–£22,450 for a 100 m² commercial roof in single-ply with insulation, including VAT at South West rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Commercial roof (100 m²), single-ply + insulation | £13,650–£22,450 |
| Single garage (18 m²), single-ply | £2,100–£3,450 |
| Single garage (18 m²), EPDM rubber | £1,650–£2,900 |
| Extension (20 m²), EPDM, new deck + insulation | £2,900–£5,050 |
Is single-ply the right system for my roof?
Single-ply is usually the right system for medium and large flat roofs, such as shops, offices, units, surgeries, clubs and blocks, where speed of installation, light weight and long life matter. On a small domestic roof it can work well, though it is not always the most economical choice.
In its favour: lightweight; quick to lay over large areas; flame-free, as the seams are welded with hot air; long typical life; welded details at rooflights and plant; lighter-coloured membranes reflect more sunlight.
Against it: only one waterproof layer, so welding quality is critical; can be punctured by foot traffic or dropped tools without walkway protection; PVC needs separating from bitumen; repairs need compatible material and welding equipment.
For a small garage or extension, EPDM is often simpler. Where people walk regularly, GRP or a liquid system may be tougher. A multi-layer torch-on felt roof gives built-in redundancy, and on older buildings mastic asphalt may be the original material. Our commercial flat roofing page covers larger jobs.
What's included?
- PVC, TPO or FPO membrane, mechanically fixed, adhered or ballasted
- Edge protection on every job and walkway protection around plant
- Hot-air welded seams, each probed along its full length
- Vapour control layer and warm-roof or tapered insulation as specified
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
Single-ply membrane roofing in Frome: questions
Do you cover Frome?
Yes. Frome is part of our Somerset coverage, including postcode districts BA11. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Frome?
Where the work needs approval it goes to Somerset Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does a single-ply roof cost in Frome?
£13,650–£22,450 for a 100 m² commercial roof in single-ply with insulation, at South West guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can a single-ply roof be repaired?
Yes. A compatible patch is cleaned and hot-air welded over the damage. Older membranes may need extra cleaning before they weld properly, which the team checks on site.
Can single-ply be used on a house?
Yes. It can be used on garages, extensions and dormers, usually adhered rather than mechanically fixed. On small domestic roofs, though, EPDM or GRP is often more economical.