Pembroke at a glance
- Postcode districts
- SA71
- Population
- about 7,552 (GeoNames)
- Council area
- Pembrokeshire County Council
- Building approval
- Pembrokeshire County Council building control, or a registered building control approver
- Nearest main town
- Haverfordwest, about 9 miles
- Guide price region
- Wales (−8% on West Midlands rates)
What do commercial flat roofs in Pembroke need?
A commercial re-roof in Pembroke has to fit around customers, staff and deliveries. We agree working hours, skip positions and access routes before we start, keep fire exits clear throughout, and choose a flame-free system where your site does not allow hot works near stock or occupied rooms.
In and around Pembroke, flat roofs are typically found on shops with flat-roofed rear stores below flats, and on bungalows with flat-roofed side extensions and dormers. Wales averages roughly 1,460 mm of rain a year, among the wettest in Britain, so we design for steady run-off: proper falls, clear outlets and upstands well above the finished roof.
How much does a commercial flat roof cost in Pembroke?
For Pembroke we use Wales rates: £12,150–£20,050 is the guide for a 100 m² commercial roof in single-ply with insulation, VAT included. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Commercial roof (100 m²), single-ply + insulation | £12,150–£20,050 |
| Condition survey and leak investigation | £140–£280 |
| Block of flats (150 m²), felt + insulation + scaffold | £14,300–£25,000 |
Do you offer condition surveys and phased budgets?
Yes. A condition survey with a written report is a paid service, guide £140–£280 for a typical single roof, with larger or multi-roof sites priced before we attend. A survey and quote for replacement work is free.
The report covers the covering, upstands, outlets, edges and rooflights, signs of ponding or wet insulation, and what needs doing now, soon and later. You can then plan a phased programme: urgent repairs first, then re-roofing in sections over one or more budget years, with each phase priced separately in your written quote.
Re-covering more than half of a roof over heated space usually triggers the thermal element rules, so the insulation is upgraded towards the renovation U-value where feasible; in England the non-domestic target is 0.18 W/m²K. We handle building control where it is needed. See building regulations and flat roof surveys.
What's included?
- Programme planned around trading hours, deliveries and site rules
- Written workmanship guarantee, with manufacturer guarantees registered where the system allows
- CDM planning, edge protection and fragile-surface controls on every job
- Single-ply, built-up felt, liquid-applied and mastic asphalt systems
Building regulations in Wales
The Welsh Approved Document L applies. Renovating more than half of a roof over a heated room means upgrading it to around 0.16 W/m²K where feasible, and new extension roofs are built to 0.13 W/m²K. Welsh Government guidance is that most re-roofing needs building control approval, so check whenever more than a quarter of a roof is replaced or repaired. We deal with the application as part of the job. More on the rules.
Which nearby areas do we also cover?
Commercial flat roofing in Pembroke: questions
Do you cover Pembroke?
Yes. Pembroke is part of our Pembrokeshire coverage, including postcode districts SA71. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Pembroke?
Where the work needs approval it goes to Pembrokeshire County Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does a commercial flat roof cost in Pembroke?
£12,150–£20,050 for a 100 m² commercial roof in single-ply with insulation, at Wales guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
What happens to air conditioning units and other roof plant?
Plant can often stay in place, with the new roof detailed around its supports. Where it has to be isolated and lifted, your mechanical contractor does that while we re-roof beneath it, and we agree the timing at survey stage.
Do you need a hot works permit?
Only if torch-on felt or other naked-flame work is used, in which case the team works under your permit system with a fire watch afterwards. Where hot works are not allowed, we specify a flame-free system such as a cold-applied membrane.