- Price per m²
- £57–£101
- Typical life
- 25–50 years
- Manufacturer guarantees
- 20-year material warranties are common
- Typical garage roof
- £1,400–£2,450
County Antrim at a glance
- Largest towns
- Lisburn, Newtownabbey, Carrickfergus, Ballymena
- Postcode areas
- BT
- Building control
- Lisburn and Castlereagh City Council, Antrim and Newtownabbey Borough Council, Mid and East Antrim Borough Council and 1 other council
- Neighbouring areas
- Belfast · County Down · County Armagh · County Londonderry
- Guide price region
- Northern Ireland (−12% on West Midlands rates)
How much does an EPDM rubber roof cost in County Antrim?
Guide prices including VAT at Northern Ireland rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,400–£2,450 |
| Extension (20 m²), EPDM, new deck + insulation | £2,450–£4,300 |
| Porch or bay (4 m²), EPDM | £650–£1,100 |
Which flat roofs are common in County Antrim?
Flat roofs in County Antrim sit on newer estates where the first extension roofs are now being replaced, bungalows with flat-roofed side extensions and dormers and shops with flat-roofed rear stores below flats. Northern Ireland averages roughly 1,150 mm of rain a year, spread over many wet days, so a roof that sheds water quickly to clear outlets lasts far longer than one that holds puddles. Approximate 1991–2020 regional averages based on Met Office data.
Building control in Northern Ireland
In Northern Ireland, renovating or replacing a roof over a heated room usually means meeting Technical Booklet F1, and building control should be contacted before work starts. Technical Booklet F1 sets roof insulation at 0.18 W/m²K when a roof over a heated room is renovated or newly built, where feasible. In County Antrim the application goes to Lisburn and Castlereagh City Council, Antrim and Newtownabbey Borough Council, Mid and East Antrim Borough Council and 1 other council. More on the rules.
Do I need building regulations approval to replace a roof with EPDM?
Often, yes. In England, Wales and Northern Ireland, re-covering more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof should be insulated towards the renovation standard where that is feasible; in Scotland, the council's building standards service decides whether a building warrant is needed.
An unheated detached garage normally falls outside these rules, and a patch repair is treated differently from a full re-cover.
In practice that means a warm roof: insulation above the deck, a vapour control layer beneath it and the EPDM on top. The extra thickness lifts the finished roof, so at survey we check door thresholds, window cills, wall flashings and upstand heights, aiming for an upstand of about 150 mm above the finished surface. Where approval is needed, we deal with building control or building standards for you. The building regulations page and our warm vs cold roof guide go into more detail.
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
Which towns in County Antrim do we cover?
EPDM rubber roofing in County Antrim: questions
Which towns in County Antrim do you cover?
All of County Antrim. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does an EPDM rubber roof cost in County Antrim?
£1,400–£2,450 for a typical 18 m² garage roof in EPDM, at Northern Ireland guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which council handles building control for a flat roof in County Antrim?
It depends on where the roof is: in County Antrim that's Lisburn and Castlereagh City Council, Antrim and Newtownabbey Borough Council, Mid and East Antrim Borough Council and 1 other council. In Northern Ireland, renovating or replacing a roof over a heated room usually means meeting Technical Booklet F1, and building control should be contacted before work starts. We confirm which applies at the survey.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.
Does an EPDM roof need maintenance?
Very little. Clear leaves from outlets and gutters, look over trims and upstands once or twice a year and after storms, and keep foot traffic to a minimum.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.
Everything about EPDM rubber roofing → · All flat roofing in County Antrim →