- Price per m²
- £62–£109
- Typical life
- 25–50 years
- Manufacturer guarantees
- 20-year material warranties are common
- Typical garage roof
- £1,500–£2,650
Cumbria at a glance
- Largest towns
- Carlisle, Barrow-in-Furness, Kendal, Whitehaven
- Postcode areas
- CA, LA
- Building control
- Cumberland Council and Westmorland and Furness Council
- Neighbouring areas
- Lancashire · County Durham · Tyne and Wear · Northumberland
- Guide price region
- North West (−5% on West Midlands rates)
How much does an EPDM rubber roof cost in Cumbria?
Guide prices including VAT at North West rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,650 |
| Extension (20 m²), EPDM, new deck + insulation | £2,650–£4,650 |
| Porch or bay (4 m²), EPDM | £700–£1,200 |
Which flat roofs are common in Cumbria?
Flat roofs in Cumbria sit on bungalows with flat-roofed side extensions and dormers, 1930s semis with flat-roofed garages and kitchen extensions and low-rise post-war blocks of flats. The North West is one of England's wetter regions, averaging roughly 1,290 mm of rain a year, so falls, outlets and well-detailed upstands matter more than the membrane colour. Approximate 1991–2020 regional averages based on Met Office data.
Building regulations in England
Replacing more than half of a roof over a heated room usually counts as renovating a thermal element, so it is insulated to current standards and notified to building control. Renovated roofs over heated rooms are insulated to around 0.16 W/m²K where that's feasible, and new extension roofs are built to 0.15 W/m²K. In Cumbria the application goes to Cumberland Council and Westmorland and Furness Council. More on the rules.
When is EPDM the right choice, and when is another system better?
EPDM is a strong choice for simple domestic roofs that people do not walk on, such as garages, single-storey extensions, porches and dormers. It is less suited to roofs with regular foot traffic or many pipes and vents.
Where it does well: few or no joins on small roofs, flexible in cold weather, tolerant of minor building movement, and laid without a flame.
Where it falls short: the finish is plain dark rubber, it can be punctured by dropped tools or sharp debris, and it is not designed as a walking surface without added protection. Roofs with many penetrations take a lot of careful detailing.
If you want a hard, walkable finish or a complex shape, GRP fibreglass often suits better. On a tight budget, or a larger roof where a layered system is preferred, torch-on felt is worth pricing. Liquid-applied roofing handles awkward details and overlays, single-ply membranes are built for larger commercial roofs, and mastic asphalt belongs on older and heritage buildings. Our EPDM vs GRP vs felt guide sets them side by side.
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
Which towns in Cumbria do we cover?
EPDM rubber roofing in Cumbria: questions
Which towns in Cumbria do you cover?
All of Cumbria. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does an EPDM rubber roof cost in Cumbria?
£1,500–£2,650 for a typical 18 m² garage roof in EPDM, at North West guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which council handles building control for a flat roof in Cumbria?
It depends on where the roof is: in Cumbria that's Cumberland Council and Westmorland and Furness Council. Replacing more than half of a roof over a heated room usually counts as renovating a thermal element, so it is insulated to current standards and notified to building control. We confirm which applies at the survey.
Can you walk on an EPDM roof?
Occasionally, for maintenance, yes, but EPDM is not designed as a regular walking surface. Where you need a route to plant or windows, walkway pads can be bonded on, or GRP may be a better fit.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.
Can an EPDM roof be fitted in winter?
Yes, as long as the deck is dry. The adhesives are affected by cold and damp, so very cold or wet days can delay bonding, and the roof is kept temporarily weathertight between dry spells.
Everything about EPDM rubber roofing → · All flat roofing in Cumbria →