- Price per m²
- £60–£107
- Typical life
- 25–50 years
- Manufacturer guarantees
- 20-year material warranties are common
- Typical garage roof
- £1,500–£2,600
Northumberland at a glance
- Largest towns
- Blyth, Cramlington, Ashington, Bedlington
- Postcode areas
- NE
- Building control
- Northumberland County Council
- Neighbouring areas
- Tyne and Wear · County Durham · North Yorkshire · Cumbria
- Guide price region
- North East (−7% on West Midlands rates)
How much does an EPDM rubber roof cost in Northumberland?
Guide prices including VAT at North East rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,500–£2,600 |
| Extension (20 m²), EPDM, new deck + insulation | £2,600–£4,550 |
| Porch or bay (4 m²), EPDM | £700–£1,150 |
Which flat roofs are common in Northumberland?
Flat roofs in Northumberland sit on low-rise post-war blocks of flats, newer estates where the first extension roofs are now being replaced and shops with flat-roofed rear stores below flats. England averages roughly 870 mm of rain a year; the North East is drier than the west but cold and windy near the coast, so wind uplift and freeze-thaw are in the specification. Approximate 1991–2020 regional averages based on Met Office data.
Building regulations in England
Replacing more than half of a roof over a heated room usually counts as renovating a thermal element, so it is insulated to current standards and notified to building control. Renovated roofs over heated rooms are insulated to around 0.16 W/m²K where that's feasible, and new extension roofs are built to 0.15 W/m²K. In Northumberland the application goes to Northumberland County Council. More on the rules.
Do I need building regulations approval to replace a roof with EPDM?
Often, yes. In England, Wales and Northern Ireland, re-covering more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof should be insulated towards the renovation standard where that is feasible; in Scotland, the council's building standards service decides whether a building warrant is needed.
An unheated detached garage normally falls outside these rules, and a patch repair is treated differently from a full re-cover.
In practice that means a warm roof: insulation above the deck, a vapour control layer beneath it and the EPDM on top. The extra thickness lifts the finished roof, so at survey we check door thresholds, window cills, wall flashings and upstand heights, aiming for an upstand of about 150 mm above the finished surface. Where approval is needed, we deal with building control or building standards for you. The building regulations page and our warm vs cold roof guide go into more detail.
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
Which towns in Northumberland do we cover?
EPDM rubber roofing in Northumberland: questions
Which towns in Northumberland do you cover?
All of Northumberland. The main towns have their own pages below, and if yours isn't listed we still cover it: send your postcode and we'll confirm.
How much does an EPDM rubber roof cost in Northumberland?
£1,500–£2,600 for a typical 18 m² garage roof in EPDM, at North East guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Which council handles building control for a flat roof in Northumberland?
It depends on where the roof is: in Northumberland that's Northumberland County Council. Replacing more than half of a roof over a heated room usually counts as renovating a thermal element, so it is insulated to current standards and notified to building control. We confirm which applies at the survey.
Does an EPDM roof need maintenance?
Very little. Clear leaves from outlets and gutters, look over trims and upstands once or twice a year and after storms, and keep foot traffic to a minimum.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.
Can an EPDM roof be fitted in winter?
Yes, as long as the deck is dry. The adhesives are affected by cold and damp, so very cold or wet days can delay bonding, and the roof is kept temporarily weathertight between dry spells.
Everything about EPDM rubber roofing → · All flat roofing in Northumberland →