Spalding at a glance
- Postcode districts
- PE11
- Population
- about 30,556 (GeoNames)
- Council area
- South Holland District Council
- Building approval
- South Holland District Council building control, or a registered building control approver
- Nearest main town
- Peterborough, about 15 miles
- Guide price region
- East Midlands (−2% on West Midlands rates)
Why choose EPDM rubber roofing in Spalding?
EPDM makes sense for a property in Spalding when the roof is a straightforward shape, such as a garage or rear extension, and nobody needs to walk on it. A single sheet leaves few joins to fail, and because it is cold-applied there is no naked flame near timber fascias or a lived-in home.
In and around Spalding, flat roofs are typically found on terraced streets with flat-roofed rear kitchens and bathrooms, and on shops with flat-roofed rear stores below flats. The East Midlands is drier than the west of Britain, so most flat roofs here fail through age, UV and poor detailing at upstands rather than sheer rainfall.
How much does an EPDM rubber roof cost in Spalding?
Guide price in Spalding: £1,550–£2,750 for a typical 18 m² garage roof in EPDM, including VAT at East Midlands rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,550–£2,750 |
| Extension (20 m²), EPDM, new deck + insulation | £2,750–£4,800 |
| Porch or bay (4 m²), EPDM | £750–£1,250 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- Strip-out of the old covering, with waste taken away
- New drip and kerb trims, outlets and upstand details
- Warm-roof insulation and vapour control layer where required
- Written workmanship guarantee, plus manufacturer guarantee registration where available
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
EPDM rubber roofing in Spalding: questions
Do you cover Spalding?
Yes. Spalding is part of our Lincolnshire coverage, including postcode districts PE11. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Spalding?
Where the work needs approval it goes to South Holland District Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Spalding?
£1,550–£2,750 for a typical 18 m² garage roof in EPDM, at East Midlands guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.
Can you put a green roof on top of EPDM?
Yes. EPDM is often used under sedum, with a protection layer, drainage and growing medium laid on top. The structure must be able to carry the extra weight, which we check before quoting.