Worthing at a glance
- Postcode districts
- BN11, BN12, BN13, BN14
- Population
- about 113,866 (GeoNames)
- Council area
- Worthing Borough Council
- Building approval
- Worthing Borough Council building control, or a registered building control approver
- Nearest main town
- Brighton, about 10 miles
- Guide price region
- South East (+10% on West Midlands rates)
Why choose EPDM rubber roofing in Worthing?
For landlords with property in Worthing, EPDM's low upkeep is the main draw: once the outlets are kept clear and the trims are checked once or twice a year, there is little else to do. It also goes down quickly on a small roof, which keeps disruption for tenants to a minimum.
Worthing's flat roofs are mostly on bungalows with flat-roofed side extensions and dormers, with plenty on low-rise post-war blocks of flats too. Much of the South East sits in the drier Thames catchment at roughly 730 mm of rain a year, so the usual failures are at joints, upstands and outlets rather than from sheer volume of rain.
How much does an EPDM rubber roof cost in Worthing?
Guide price in Worthing: £1,750–£3,100 for a typical 18 m² garage roof in EPDM, including VAT at South East rates. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), EPDM rubber | £1,750–£3,100 |
| Extension (20 m²), EPDM, new deck + insulation | £3,100–£5,350 |
| Porch or bay (4 m²), EPDM | £850–£1,400 |
How are the joins, edges and upstands made watertight on an EPDM roof?
They are bonded with contact adhesive and sealed with purpose-made EPDM tapes and pre-formed pieces, because the edges and details are where most rubber roof leaks start.
- Wall upstands: the rubber is turned up the wall, usually to about 150 mm above the finished roof, fully bonded, then finished with a termination bar or a cover flashing chased into the masonry.
- Corners: folded rather than cut where possible, or finished with pre-formed pieces.
- Joins: on roofs wider than one sheet, the laps are cleaned, primed and joined with splice tape, then rolled firmly.
- Pipes and vents: sealed with pre-formed pipe boots rather than relying on mastic.
- Edges and outlets: drip and kerb trims are fixed and the junction with the membrane is sealed with cover tape; outlets are bonded into the membrane at the lowest point.
We also check the falls before laying, because standing water around an outlet shortens the life of any detail. There is more on this in our pages on edges and drainage and rooflight upstands.
What's included?
- EPDM membrane fully bonded, in one sheet where the roof size allows
- Strip-out of the old covering, with waste taken away
- Written workmanship guarantee, plus manufacturer guarantee registration where available
- Deck check and replacement of soft or rotten boards
Building regulations in England
Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.
Which nearby areas do we also cover?
- Lancing · 2 mi
- Shoreham-by-Sea · 5 mi
- Portslade · 7 mi
- Littlehampton · 7 mi
- Brighton · 10 mi
- Bognor Regis · 14 mi
EPDM rubber roofing in Worthing: questions
Do you cover Worthing?
Yes. Worthing is part of our West Sussex coverage, including postcode districts BN11, BN12, BN13, BN14. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Worthing?
Where the work needs approval it goes to Worthing Borough Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does an EPDM rubber roof cost in Worthing?
£1,750–£3,100 for a typical 18 m² garage roof in EPDM, at South East guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
How long does it take to fit an EPDM roof?
A single garage typically takes one to two days and an insulated extension roof two to three, weather permitting. Larger roofs, scaffold and complex details add time.
Can a punctured EPDM roof be repaired?
Usually, yes. The area is cleaned and primed, then an EPDM patch or cover tape is bonded over the damage. If water has reached the deck, a survey first is sensible.