Flat RoofingContractors

Flat roof systems

Torch-on felt roofing in Havant

For blocks of flats, shops and houses in Havant, torch-on felt remains a practical way to re-roof at a sensible cost. Each job follows the same pattern: survey, written quote, strip and lay, then a fire watch and a walk-round with you before we hand over the written workmanship guarantee.

Roofer torching a slate-grey mineral cap sheet on a commercial flat roof behind edge protectionComputer-generated example image

Havant at a glance

Postcode districts
PO9
Population
about 45,574 (GeoNames)
Council area
Havant Borough Council
Building approval
Havant Borough Council building control, or a registered building control approver
Nearest main town
Portsmouth, about 6 miles
Guide price region
South East (+10% on West Midlands rates)

Why choose torch-on felt roofing in Havant?

Where a flat roof in Havant already has a felt covering and the building owner wants like-for-like, torch-on is the natural replacement. The old roof is stripped, the deck checked and the new layers laid, often with warm-roof insulation added when the space below is heated.

In and around Havant, flat roofs are typically found on low-rise post-war blocks of flats, and on bungalows with flat-roofed side extensions and dormers. Much of the South East sits in the drier Thames catchment at roughly 730 mm of rain a year, so the usual failures are at joints, upstands and outlets rather than from sheer volume of rain.

How much does a torch-on felt roof cost in Havant?

At South East guide rates, a typical 18 m² garage roof in torch-on felt comes to £1,650–£2,900 including VAT. The fixed price comes after a free survey for new and replacement roofs.

JobGuide price inc VAT
Single garage (18 m²), torch-on felt£1,650–£2,900
Extension (20 m²), felt, new deck + insulation£3,000–£5,150
Block of flats (150 m²), felt + insulation + scaffold£17,100–£29,900
Single garage (18 m²), EPDM rubber£1,750–£3,100
Extension (20 m²), EPDM, new deck + insulation£3,100–£5,350

Is torch-on roofing safe, and what is the difference between two- and three-layer systems?

Yes, torch-on is safe when hot works are properly controlled, because most roof fires linked to torching start at hidden timber or debris near edges and upstands, not on the open roof. Our teams follow a hot-works routine on every job:

  • check eaves, fascias, soffits and wall cavities for timber, nests and debris before lighting a torch;
  • use a cold-applied or self-adhesive membrane, rather than a flame, at edges, against combustible materials and in tight details;
  • keep fire extinguishers on the roof and the gas bottles secured and away from the work;
  • stop torching well before the team leaves, then carry out a fire watch so smouldering is spotted while people are still on site.

As for layers, a two-layer system (underlay plus cap sheet) is common on domestic roofs such as garages and extensions. A three-layer system adds an intermediate sheet, giving more thickness and redundancy, and is often specified on larger, commercial and multi-occupied roofs. The right choice depends on the size and use of the roof and the system's requirements, so we set it out in the quote.

Near a boundary, the external fire performance of the tested build-up, such as a BROOF(t4) classification, can also matter, and we check it where it applies.

What's included?

  • Hot-works checks and fire watch on every torch-on job
  • Deck inspection with replacement of damaged boards
  • Two- or three-layer reinforced bitumen membrane with staggered laps
  • Vapour control layer and warm-roof insulation where needed

Building regulations in England

Replacing more than half of a flat roof over a heated room usually counts as renovating a thermal element, so the roof is insulated to around 0.16 W/m²K where that's technically and economically feasible, and the work is notified to building control: the council or a registered building control approver, unless a registered competent person self-certifies it. A roof on a new extension is built to 0.15 W/m²K. Patch repairs, and most unheated detached garages, don't trigger the upgrade. Structural changes, or a new covering that adds 15% or more to the roof's weight, also need approval. More on the rules.

Which nearby areas do we also cover?

Torch-on felt roofing in Havant: questions

Do you cover Havant?

Yes. Havant is part of our Hampshire coverage, including postcode districts PO9. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.

Who checks building regulations for a flat roof in Havant?

Where the work needs approval it goes to Havant Borough Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.

How much does a torch-on felt roof cost in Havant?

£1,650–£2,900 for a typical 18 m² garage roof in torch-on felt, at South East guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.

Can I paint or coat an old felt roof?

Reflective or liquid coatings can extend the life of a sound felt roof, but they will not fix wet insulation, a rotten deck or poor falls. A survey shows whether coating or replacement makes more sense.

Is torch-on suitable for a block of flats?

Yes, layered bitumen systems are widely used on blocks of flats and commercial buildings. Larger roofs often use three layers and insulation, with hot works planned around residents.

Other flat roof work in Havant

Torch-on felt roofing in Havant: get a fixed price

Free survey and a written fixed quote for replacement and new roofs. No obligation.

Call usGet a guide price