Milford Haven at a glance
- Postcode districts
- SA73
- Population
- about 13,582 (GeoNames)
- Council area
- Pembrokeshire County Council
- Building approval
- Pembrokeshire County Council building control, or a registered building control approver
- Nearest main town
- Haverfordwest, about 7 miles
- Guide price region
- Wales (−8% on West Midlands rates)
Why choose torch-on felt roofing in Milford Haven?
For a commercial roof in Milford Haven, such as a shop, surgery or club, torch-on felt offers a hard-wearing mineral finish that takes occasional maintenance traffic. Phased work keeps part of the building weathertight while the rest is re-roofed, so the business can usually keep trading.
In a town like Milford Haven, flat roofs are commonly found on bungalows with flat-roofed side extensions and dormers or lock-up garage blocks on estates. Wales averages roughly 1,460 mm of rain a year, among the wettest in Britain, so we design for steady run-off: proper falls, clear outlets and upstands well above the finished roof.
How much does a torch-on felt roof cost in Milford Haven?
For Milford Haven we use Wales rates: £1,400–£2,400 is the guide for a typical 18 m² garage roof in torch-on felt, VAT included. The fixed price comes after a free survey for new and replacement roofs.
| Job | Guide price inc VAT |
|---|---|
| Single garage (18 m²), torch-on felt | £1,400–£2,400 |
| Extension (20 m²), felt, new deck + insulation | £2,500–£4,300 |
| Block of flats (150 m²), felt + insulation + scaffold | £14,300–£25,000 |
| Single garage (18 m²), EPDM rubber | £1,450–£2,600 |
| Extension (20 m²), EPDM, new deck + insulation | £2,600–£4,500 |
Is torch-on roofing safe, and what is the difference between two- and three-layer systems?
Yes, torch-on is safe when hot works are properly controlled, because most roof fires linked to torching start at hidden timber or debris near edges and upstands, not on the open roof. Our teams follow a hot-works routine on every job:
- check eaves, fascias, soffits and wall cavities for timber, nests and debris before lighting a torch;
- use a cold-applied or self-adhesive membrane, rather than a flame, at edges, against combustible materials and in tight details;
- keep fire extinguishers on the roof and the gas bottles secured and away from the work;
- stop torching well before the team leaves, then carry out a fire watch so smouldering is spotted while people are still on site.
As for layers, a two-layer system (underlay plus cap sheet) is common on domestic roofs such as garages and extensions. A three-layer system adds an intermediate sheet, giving more thickness and redundancy, and is often specified on larger, commercial and multi-occupied roofs. The right choice depends on the size and use of the roof and the system's requirements, so we set it out in the quote.
Near a boundary, the external fire performance of the tested build-up, such as a BROOF(t4) classification, can also matter, and we check it where it applies.
What's included?
- Deck inspection with replacement of damaged boards
- Vapour control layer and warm-roof insulation where needed
- Mineral-finished cap sheet, upstands, outlets and edge trims
- Strip-off of the existing roof covering and removal of waste
Building regulations in Wales
The Welsh Approved Document L applies. Renovating more than half of a roof over a heated room means upgrading it to around 0.16 W/m²K where feasible, and new extension roofs are built to 0.13 W/m²K. Welsh Government guidance is that most re-roofing needs building control approval, so check whenever more than a quarter of a roof is replaced or repaired. We deal with the application as part of the job. More on the rules.
Which nearby areas do we also cover?
Torch-on felt roofing in Milford Haven: questions
Do you cover Milford Haven?
Yes. Milford Haven is part of our Pembrokeshire coverage, including postcode districts SA73. Surveys and roofs are carried out by vetted roofing teams working under S&K Property Investments and Improvement Ltd.
Who checks building regulations for a flat roof in Milford Haven?
Where the work needs approval it goes to Pembrokeshire County Council building control, or a registered building control approver. We tell you at the survey whether your job needs it and deal with the paperwork as part of the quote.
How much does a torch-on felt roof cost in Milford Haven?
£1,400–£2,400 for a typical 18 m² garage roof in torch-on felt, at Wales guide rates including VAT. The fixed price comes after a free survey for new and replacement roofs.
Can torch-on felt be laid in wet weather?
Not in rain or on a wet deck, because moisture trapped under the membrane causes blisters. Light cold weather is usually workable, but we will postpone rather than lay on a damp surface.
Why does my felt roof have blisters?
Blisters usually form when moisture or air trapped beneath the felt expands in the sun. A few small, intact blisters may be monitored, but widespread or split blisters point to a repair or replacement.